Plate Shear - Mechanical

sheet width 2000 mm︱plate thickness 2,25 mm︱distance between columns 2040 mm︱total power requirement 7,5 kW︱weight of the machine ca. 1,5 t︱dimensions of the machine ca. 2,2x1,7x1,1 m︱

---

sheet width 2040 mm︱plate thickness 1,5 mm︱distance between columns mm︱total power requirement kW︱weight of the machine ca. 1 t︱dimensions of the machine ca. m︱

---

guillotine shears, used, Manufacturer: RAS, Type: 53.30, Year of manufacture: 1966, weight: 920 kg, Usable length: 2040 mm, Max. sheet thickness: 1,5 mm

sheet width 1040 mm︱plate thickness 2,50 mm︱no. of strokes 63 Hub/min︱cutting angle 1,66 °︱column arm 100 mm︱table height ca. 750 mm︱total power requirement 3,0 kW︱weight of the machine ca. 750 kg︱range L-W-H 1470 x 1550 x 1020 mm︱

---

** Refurbished - shear blades sharpened ** like New (!!) Furnishing: - manual backgauge 0-550 mm - with analogue measuring scale and magnifying glass - adjustable in front, by adjusting lever - 1x long side stop 850 mm - free-moving footswitch - Scratch protection on support table

sheet width 1040 mm︱plate thickness 2,50 mm︱no. of strokes 63 Hub/min︱cutting angle 1,66 °︱column arm 100 mm︱table height ca. 750 mm︱total power requirement 3,0 kW︱weight of the machine ca. 750 kg︱range L-W-H 1470 x 1550 x 1020 mm︱

---

** Refurbished - shear blades sharpened ** like New (!!) Furnishing: - manual backgauge 0-550 mm - with analogue measuring scale and magnifying glass - adjustable in front, by adjusting lever - 1x long side stop 850 mm - free-moving footswitch - Scratch protection on support table * Machinevideo : https://www.youtube.com/watch?v=8cb4EqRUxIs

sheet width 1040 mm︱plate thickness 2,50 mm︱distance between columns mm︱total power requirement kW︱weight of the machine ca. 0,750 t︱dimensions of the machine ca. m︱

---

Manual back gauge can be operated from the front up to 500 mm Side stop Knife sharpened

sheet width 2540 mm︱plate thickness 2 mm︱strokes per minute until 63 ︱throat 100 mm︱cutting angle 1,13 °︱table height 750 mm︱table width 320 mm︱table height over floor 750 mm︱total power requirement 3 kW︱weight of the machine ca. 1600 kg︱dimensions of the machine ca. 3,1 x 2 x 1,3 m︱Electric 380 Volt ︱Rear register front operated 15 - 550 ︱Foot switch ︱Squaring arm ︱Support arms 3 x ︱Rear sheet tray ︱

---

Motorized guillotine shears in the swing cutting system with adjustable from the front manual backgauge with analogue display and reading optics. Power transmission via gearbox, eccentric shaft and connecting rod on the cutter bar. Less noise level because the gear is only switched on during the cutting process is. Hold-down beam with continuous pressure element made of elastomers material that ensures secure clamping of the sheet metal. The cutting performance refers to 400 N/mm² strength. The machine was used in air duct construction and only cut sheets of 1 mm. Machine dealer with own stock of 1600 m².

sheet width 2040 mm︱plate thickness 3,00 mm︱thickness at "Niro-steel" 1,50 mm︱no. of strokes 50 Hub/min︱cutting angle 1.4 Grad︱table height 750 mm︱distance between columns 2120 mm︱back stop - adjustable 1.0 - 550 mm︱column arm 100 mm︱Control manuell ︱engine output 5.5 kW︱weight of the machine ca. 2050 kg.︱range L-W-H 2600 x 1980 x 1400 mm︱

---

Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display * adjustable from the front * Continuous adjustment over the entire travel range * Adjustment range 1.0 - 550 mm - Machine side stand with projection .. 100 mm - manual cutting gap adjustment - 1x hold-down bar - 1x long side stop - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - 2x EMERGENCY stop buttons at the front - Connection cable including plug - original instruction manual

sheet width 2040 mm︱plate thickness 3.0 mm︱thickness at "Niro-steel" 1.5 mm︱no. of strokes 50 Hub/min︱cutting angle 1.4 Grad︱table height 750 mm︱distance between columns 2120 mm︱back stop - adjustable 1.0 - 550 mm︱column arm 100 mm︱Control manuell ︱engine output 5.5 kW︱weight of the machine ca. 2050 kg.︱range L-W-H 2600 x 1980 x 1400 mm︱

---

Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display * adjustable from the front * Continuous adjustment over the entire travel range * Adjustment range 1.0 - 550 mm - Machine side stand with projection .. 100 mm - manual cutting gap adjustment - 1x hold-down bar - 1x long side stop - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - 2x EMERGENCY stop buttons at the front - Connection cable including plug - original instruction manual * Machine link: http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008-9325338

sheet width 2540 mm︱plate thickness 2 mm︱thickness at "Niro-steel" 1,25 mm︱no. of strokes 63 Hub/min︱cutting angle 1,13 °︱table height 750 mm︱table width 320 mm︱back stop - adjustable 5,0-550 mm︱total power requirement 3 kW︱weight of the machine ca. 1600 kg︱dimensions of the machine ca. 3100x2000x1400 mm︱

---

Equipment: - manual backgauge, with analog display * Adjustable from the front * stepless adjustment over the entire travel range - 1x long side stop - 3x support arms - Free-moving foot switch - Sheet holding device for thin sheet blanks