Outside profiling machine
Machinelist: Outside profiling machine
Outside profiling machine
- Engelfried Maschinentechnik GmbH
- Elisabethenstr. 41
- 73432 Aalen
- Deutschland
-
(0049)07361-98660
(0049)07361-986640 -
info@engelfried.com
www.engelfried.com
#1305-6828 · Outside profiling machine
Okoma - UF 2 EG mit Schleifeinheit - - gebraucht -
Technical details
1 OKOMA folding machine model UF 2 EG ------------------------------------- 1. Energy data: - Operating voltage: 3 phases, 380 V, 50 Hz. - Compressed air: Air requirement: 13 NL/min. Operating pressure: 8 bar up. Air: according to Pneurop 6611 2. Profile spindle 1: - Spindle arrangement: right - Power 11 kW - Speed ??7000 rpm - Direction of rotation: synchronous and counter rotation - Spindle diameter 40 mm - Usable length 252 mm - Tool diameter max. 230 mm - U-movement of the profile spindle - Positioning vertically Drive: pneumatic cylinder 120 mm cycle for 2 tool positions Position sensor: limit switch - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch - Automatic immersion: immersion speed can be regulated for tear-free Fold over - Protective and suction hood with connecting piece 140 mm diameter. 3. Profile spindle 2: - Spindle arrangement: right - Power 11 kW - Speed ??7000 rpm - Direction of rotation: counter rotation - Spindle diameter 50 mm - Usable length 272 mm - Tool diameter max. 230 mm - U-movement of the profile spindle - Positioning vertically Drive: pneumatic cylinder 90 mm cycle for 3 tool positions Position sensor: limit switch - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch - Protective and suction hood with connecting piece 140 mm diameter. 4. Fitting milling device EG: - Spindle arrangement on the right - Drive: three-phase motor 3 kW - Speed ??6000 rpm - Spindle diameter 30 mm - Usable length 47 mm - Vertical positioning: none - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch (rear only) - Protective and suction hood with connection piece 80mm diameter 5. Stop: - 1st stop: in front of spindle 1 manual chip removal Quick adjustment via. parallelogram - 2nd stop: between spindles 1 and 2 Chip removal: pneumatically adjustable - 3rd stop: after spindle 2 Fixed stop 6. Grinder with automatic immersion and immersion 7. Feed: - Roller distance from axle to axle 130 mm - Roll diameter 110 mm - Roll width 50 mm - Feed can be swiveled away - with pneumatic travel control 8. Support rail for milling: - Rail length: approx. 3000 mm - Adjustment range forward: approx. 100 - 600 mm 9. Electrical control: - Programmable logic controller: Siemens electronics PC control, 30 programs, 380 V., 50 Hz. - Power section: Siemens S 5 - Non-contact limit switches More pictures on request! --------------------------- (technical data according to manufacturer - no guarantee!)
Datasheet
Request / Contact
- Engelfried Maschinentechnik GmbH
- Elisabethenstr. 41
- 73432 Aalen
- Deutschland
-
(0049)07361-98660
(0049)07361-986640 -
info@engelfried.com
www.engelfried.com
#1305-6827 · Outside profiling machine
WEINIG - Univar 6 P - - gebraucht -
Technical details
Weinig Univar 6 P In order to sell ---------------------- Operating voltage: 380 volts, 50 periods. For milling around windows, doors and similar with uneven edges Profiles. Arrangement of the aggregates: 1. Synchronous spindle on the right, pneumatically clocked. 2. Profiling spindle on the right 3. Fitting spindle Profiling spindle suitable for holding several tools one on top of the other. Spindle movement pneumatic. The 1 spindle works in synchronization for tear-free milling. Respectively This spindle plunges the last 100 mm of a frame end with the Insert the appropriate tool into the wood to prevent tearing at the frame corners avoid. Machine stands, tables, stops: Machine body made of heavy, torsion-free and vibration-damping elements. Stops on the right in the profiling area made of Pertinax. Before Profiling spindle a split stop with sliding bar for short parts. Additional opening rail for large format frames. Feed system: Continuous, chainless feed equipped with rubber rollers. Blow-off device for feed rollers and table. Spindles, hood: Spindles with high concentricity and dynamically balanced. Extraction hoods designed for the cheapest chip flow. Easiest tool change Quick-opening hood lid. Machine operation, setting aids: Operating the machine from the front. Setting the stops for Tool diameter using mechanical number display. Machine electrics, motors, controls: Electrical design according to DIN VDE 0113 - Electrical equipment from Industrial machines EN 60204 IEC 204-1. Further electrical regulations are not taken into account. Engines dynamically balanced. Control of tool positions via selector switch on the control panel. Tools: Machine equipped with operating tools, but without Editing tools. SPINDLE 1 Synchronous spindle Number of tools: 1 Spindle speed: 6000 rpm Spindle diameter: 50mm Tool clamping length: 120 mm Tool diameter max. (milling): 232 mm Tool zero flight circle: 112-140 mm Basic position under table: 10 mm Motor strength: 4 KW (5.5 KW) SPINDLE 2 Number of tools: 4 Spindle stroke vertical: 3 x 80 mm = 4 tools Can be switched to 2 x 95 mm = 3 tools Spindle speed: 6000 rpm Spindle diameter: 50mm Tool clamping length: 320 mm Feed profiling unit: 8 m/min Feed roller width: 50mm/35mm Feed roller diameter: 95 mm Stop height: 70 mm Working width: min. 30 mm; max. 220 mm Working height: min. 30 mm; max. 100mm Workpiece length without tenon: min. 245 mm Tool diameter max. For zero diameter 112 mm: 210 mm For zero diameter 140 mm: 232 mm Tool diameter max. (milling): 232 mm Tool zero flight circle: 112-140 mm Basic position under table: 10/5 mm Motor strength: Spindle: 11 KW Feed: 1.1 KW Feed profiling unit: continuously 6-12 m/min Feed roller width: 50 mm Feed roller diameter: 95 mm Stop height: 70 mm Working width: min. 30 mm; max. 220 mm Working height: min. 30 mm; max. 100mm Workpiece length without tenon: min. 245 mm Special equipment: 3 Mechanical spindle brake for synchronous spindle, profiling spindle and Additional aggregates SPINDLE 3 1 fitting milling unit, right: for milling the fitting groove in the Milling pass or for grooving in the longitudinal profile. Pneumatic horizontal movement with selector switch in the control panel. Motor power: 2.2 KW Speed: 6000 rpm Spindle diameter: 40mm Clamping height: 125 mm Tool flight circle: min. 140 mm; max. 180 mm Basic position below table level: 10 mm Motor reinforcement for synchronous spindle from 4 KW to 7.5 KW Motor reinforcement for profiling spindle from 5.5 KW to 11 KW Screen controls for 99 window types. 1 type can hold up to 8 different parts contain. Manufacturing options: individual parts, milling. Data entry via Keyboard with integrated operator guidance and error diagnosis. Free-standing control cabinet --------------------------------- (technical data according to manufacturer - no guarantee!)
Datasheet
Request / Contact
- Engelfried Maschinentechnik GmbH
- Elisabethenstr. 41
- 73432 Aalen
- Deutschland
-
(0049)07361-98660
(0049)07361-986640 -
info@engelfried.com
www.engelfried.com
#1305-2706 · Outside profiling machine
WEINIG - Univar 10/3 - - gebraucht -
Technical details
Weinig Univar 10/3 folding machine --------------------------------- Machine will be cleaned and chcked before delivery For milling around windows, doors and the like with uneven circumferential profiles. Machine suitable for wood thickness 68 to 92 mm Time required per frame milling, medium size 1.20 x 1.20 m - approx. 2 minutes. The available tool positions are selected using a selector switch on the control panel retrieved. Machine with 3 hydraulically controlled right precision Lifting spindles for holding 3 tool sets, 2 x 95 mm spindle stroke per spindle The spindle stroke takes place in a U-movement, so that the opening is possible for short parts The milling stop remains as small as possible. Spindle stroke horizontally fine Adjustable for both tool positions from the operator side. Central lubrication for the spindle units. The 1. Spindle can be selected in right-left rotation. This spindle dips the last 100 mm of each frame end appropriate synchronization tool into the passing wood. Through this This prevents the tool of the subsequent milling spindle from running in the opposite direction working, causing tearouts. Excavation of the first 7 transport rollers using Footswitch. This shortens the lead time. An additional The support rail also allows large-format frames to be milled around. Continuous, chainless rubber roller feed with extreme short roller spacing. Height adjustment of the feed bar electrically readable. Electrical version according to VDE. Machine including operating tools, but without processing tools tools. Technical data: Working width min. 40 mm Working height min. 30 mm, max. 100 mm 1. Profiling spindle (synchronous and counter-rotation) -------------------------------------------------- -- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm with synchronous automatic immersion 2. Profiling spindle ---------------------- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 3. Profiling spindle ---------------------- Motor strength lifting spindle 11.0 kW Spindle speed 6000 rpm Spindle diameter 50 mm Clamping length 285 mm Tool zero flight circle 112 - 140 mm Max. tool - D : 232 mm Spindle stroke vertical 2 x 95 mm for 3 tools Basic position under table 10 mm (adjustable up to 20 mm) Spindle stroke horizontal 80 mm 4. Profile spindle - fitting unit on the right ------------------------------------------------- For milling the fitting groove in the milling cycle or for grooving in the longitudinal profile. Pneumatic horizontal movement with Selector switch in the control panel. Motor 2.2 KW Speed 6,000 rpm Spindle diameter 40 mm Clamping height 125 mm, 2 tools Tool flight circle min. 140 mm, max. 180 mm Motor power feed 1.1 kW Feed speed 6 - 12 m/min. Feed rollers - D : 95 mm Feed roller width 50/30 mm Feed roller spacing 100/120 mm -------------------------------- Screen control with 150 programs. 1 program is each 1 individual part and includes 2 end profiles and 1 longitudinal profile. Pro programs are for end processing 20 different profiles can be selected for Longitudinal machining of 40 different profiles 1 can be selected (in turning mode 2). When manufacturing, e.g. a frame, up to 8 different programs (parts) can be saved. The program memory can be organized so that up to 18 frames or sashes with a maximum of 8 parts each can be stored. Manufacturing options: - Individual parts - Double parts - frame by frame - in series - Milling Data entry via keyboard with integrated Operator guidance and error diagnosis. ---------------------------------- Length: 4000mm (Length of frame milling ruler: 4500 mm) Width: 2000mm Height: 2200mm (Technical information according to the manufacturer, no guarantee!)
Datasheet
Request / Contact
Профіль трейдера: Engelfried Maschinentechnik GmbH
Зв'язатися з трейдером
Engelfried Maschinentechnik GmbH
Elisabethenstr. 41
73432 - Аален
Німеччина
(0049)07361-98660">(0049)07361-98660
(0049)07361-986640
info@engelfried.com
www.engelfried.com
Elisabethenstr. 41
73432 - Аален
Німеччина
(0049)07361-98660">(0049)07361-98660
(0049)07361-986640
info@engelfried.com
www.engelfried.com
Профіль Трейдера
Компанія Gebrüder Engelfried oHG
Elisabethenstrasse 41
73432 Aalen-Unterkochen
Німеччина
Тел. + 49 (7361) 9866-0 Вернер та Флоріан Енгельфід
Тел. + 49 (7361) 9866-0 Флоріан Енгельфред
kom 0602392773 Маріан Гржешкевич
Тел .: + 49 (7361) 9866-19 Кирилл Суппес
Факс: + 49 (7361) 8431
info (at) engelfried.com
Виставка та склад:
Gewerbegebiet
Kapellenweg 25
73447 Оберкочен
Німеччина
Телефон + 49 (7364) 919323
Engelfried Maschinentechnik GmbH
Elisabethenstr. 41
Contact Trader
Engelfried Maschinentechnik GmbH
Elisabethenstr. 41
73432 - Aalen
Deutschland
(0049)07361-98660
(0049)07361-986640
info@engelfried.com
www.engelfried.com
Contact person:
Elisabethenstr. 41
73432 - Aalen
Deutschland
(0049)07361-98660
(0049)07361-986640
info@engelfried.com
www.engelfried.com
Contact person:
Machine category
Abrichthobelmaschine · Band- und Profilschleifmaschine · Bandsäge · Beschlagcenter · Bohr- und Dübeleintreibmaschine · Breitbandschleifmaschine · Clipsetzer fuer Holz-Alufenster · CNC-Bearbeitungszentrum · CNC-Bearbeitungszentrum Fenster u. Türen · Dickenhobelmaschine · Doppelgehrungssäge · Dreh- und Kipptisch · Ecklager- und Olivenbohrmaschine · Entstauber · Fensteranlage · Fensterlackieranlage · Fensterwerkzeuge · Formatkreissäge · Fräsmaschine · Furnierklebegerät · Furnierpresse · Füge- und Feinschnittmaschine · Glasleistensäge · Kantenschleifmaschine · Kapp- und Gehrungssäge · Keilzinkenanlage · Klammergeräte · Kombinierte Abricht- und Dickenhobelmasc · Kommissionswagen · Kompressor · Kreuzsprossenfräse · Lamellierpresse · Leimauftragsmaschine · Leimgerät · Längskreissäge · Längsschnittkreissäge · Minizinkenpresse · Montagestation · Olivenbohrmaschine · Optimierungskappsäge · Plattensägen vertikal · Profilwagen · Rahmen- und Langlochbohrmaschine · Rahmenpresse · Rollenbahn · Rundbogenfräsgeräte · Schleifmaschine · Schwenkfräsmaschine · Transportanlage · Transportwagen · Umfälzautomat · Universal-Dübellochbohrmaschine · Untertischkappsäge · Verglasungs- und Kontrollpresse · Verleimstern · Vierseitenhobelmaschine · Werkstückrückführung · Werkzeug-Reinigungsgeräte · Zapfenschneid- und Schlitzmaschine · Zerspanen ·