'
Європейська мережа дилерів акціонерної техніки

Bitte einen Suchbegriff eingeben - Будь ласка, введіть пошуковий термін
Категорія:
    Виробник:
      машини:
        Трейдер:

          Other Metal Processing

          Machinelist: Other Metal Processing


          Balancing Machine

          used Other Metal Processing Balancing Machine SCHENCK HM 40/HM20 MOBIL


          • SKM Industriemaschinen
          • Röntgenstr. 3
          • 89264 Weißenhorn
          • Deutschland

          • +49 (0) 7309 954 986 0
            +49 (0) 7309 954 986 1
          • info@skm-maschinen.de
            www.skm-maschinen.de
          #2032-1731 · Balancing Machine

          SCHENCK - HM 40/HM20 MOBIL - - 2012/ 2021 - CAP920

          Technical details
          workpiece weight 100 - 3.000 kg︱workpiece length 5.000 mm︱diameter 1.260 - 1.600 mm︱Control CAP920 ︱total power requirement 11 kW︱weight of the machine ca. 20 t︱dimensions of the machine ca. 20" Container m︱
          Mobile balancing system "SCHENCK" for use anywhere in the world The balancing system is permanently installed in a 20" open-top container. The container is equipped with everything you need for balancing • Lighting • Metal base plate 12,000 kg as a base plate for accuracy • Compressor for working air supply distributed in the container • Compressed air connections. • A circumferential power strip • A tool cabinet equipped with tools • A hydraulic lifting device for aligning the container from the outside • In addition to a tarpaulin for the roof, the container also comes with movable roof segments made of sheet metal. • The container has a central plug through which the container can be connected can be supplied with the required 380V voltage. The system has been approved by Schenck and test protocols are available On the following pages please find the specification for 1 Schenck balancing machine, type HM 40/HM 20 U/BU with measuring unit CAB 920 SmartTouch We like to give you some technical comments to this balancing machine. This machine exists in its basic version of a HM 40 U/BU. Additionally we are offering a special pair of add. pedestals type HM 20 which can be easily exchanged against the HM 40 pedestals. The HM 20 pedestals will enable you to accommodate also small pump rotors into the machine. The advantages are: only one machine base and end and belt drive with one electrical control (space cost-saving) The machine is installed in a open Top 20” Container as a safety enclosure. (space and cost-saving) The HM 40/20 U/BU covers a wide range of rotor types due to rotor weight, dimension and balancing tolerances. This may also require fiexibility in balancing speeds. Therefore we have quoted the machine together with an electrical drive with squirrel cage motor with frequency converter for variable speed. The offered measuring unit CAB 920 is a computerized high-end unit and especially developed to fulfil advanced balancing tasks. Data input is extremely simple through the "Easy Mode" guiding the Operator perfectly. Unbalance visualization is realized by big vector meter displays on a high contrast TFT colour monitor with touch screen function. The integrated Industrial PC runs the unique CAB 920 balancing software and provides access to the balancing Data for direct printouts or via PC network. CAB 920 can be adapted to specific needs by additional software packages. For quick and accurate finding of the angular position of the measured unbalance on the rotor by using the belt-drive the software extension 'angle indexing" is included in the delivery extent of both measuring units. When reaching the correet unbalance angle it will be displayed on the measuring unit. Due to the method of correction (grinding at a [arger surface area) the vector indication is of advantage. Machine mode: HM 40/20 U/BU Year of manufacturing: 2012/2021 Manufacturing number: RPHF02I7 Item Extent of delivery Pair Bearing Pedestals HM 40 Rotor weight for symmetric bad 3000 kg for each bearing pedestal max. 1500 kg Largest rotor diameter above machine bed 1600 mm Distance between bearing centres (belt drive between pedestals) min. 155 mm upward static bearing loads for counter bearing with roller 3000 N Limit value of permanent calibration 710 x 1 0E6 kg/min' 1.1 1 Pair of Roller Bearing lnserts HM 40 adjustable for journal bearing diameters 1.2 1 Pair of Roller Bearing Inserts HM 40 adjustable for journal bearing diameters 1.3 1 Pair Bearing Pedestals HM 20 Rotor weight for symmetric bad for each bearing pedestal max. Largest rotor diameter above machine bed Distance between bearing centres (left drive between pedestals) upward static bearing loads for counter bearing with roller Limit value of permanent calibration 1 Pair of Roller Bearing lnserts adjustable for journal bearing diameters 9-70 mm 1 Pair of Roller Bearing lnserts adjustable for journal bearing diameters 70-140 mm 2 Set of counter bearings (Hold-down bracket) The balancing machine is equipped for safety reasons with one set of counter bearings size HM 40 and one set size HM 20 to absorb upward bearing loads. The counter bearings are hinged and tHting out of the way for easy rotor loading and unboading. Each set is consisting of: - 1 x counter bearing with roh (negative bad bearing for overhanging rotors) - 1 x counter bearing with sliding piece 1.7 2 Axial thrust stops mounted on machine base Two axial thrust stops to be mounted on machine base for babancing big rotors in overhanging position. 2 1 Machine Bed with roller chain and two T-slots for moving the pedestals easily along the machine base bed Iength in total consisting of 5.000 mm 1 x3000mm, 1 x2000mm 3 1 Measuring Unit with: Operating System Windows 10 loT Enterprise 2016 LTSB - Direct data input without keyboard via Touch-Screen-Display - Easy Mode for simplified data input and display of results - Indication of the result via big vectormeter and numerical displays - Workshop tried and tested industrial PC - Easy data export via front side USB - Networking capability - Optimized signal processing for high accuracy via Schenck MMD-digital filter - Intelligent self-diagnostics of the measuring electronics - Modular, service friendly System design - Operation using Windows standard procedures - Measurement of dynamic, static and couple unbalance - Optimised menu functions - Rotorfile Wizard - Possibility to connect drawings or instructions to rotor files - User level administration with individual profiles - Numerous software modules available - mcl. Software 'Tolerance Calculation to [SO 21940-11 - mcl. single, key- and index compensation - mdl. measurement during run-up - Advanced print manager - Log report in pdf format - Archiving in measurement value database in MS-Excel compatible format - User dialog can be selected between English/German Measuring range 100 – 5000 rpm Minimum achievable residual unbalance (Umar) acc. ISO 2953 for each plane per kg rotor weight with belt-drive 0.1 gmm/kg with end-drive 0.5 gmm/kg but for HM 20 pedestals not less than 0.8 gmm but for HM 40 pedestals not less than 4.0 gmm Value refers to the measuring speed of 1000 rpm Unbalance reduction ratio (URR) up to 95% 3.1 1 Indexing manually to exactly transfer the measured unbalance angle to the rotor (manual indexing). 3.2 1 Software "Rotorspecific Calibration" Our optional Rotor Specific Calibration software allows a "fine tuning" of the machine to compensate for balancing tooling whose dynamic stiffness is insufficient. The Rotor Specific Calibration software will improve the ability to transpose the bearing plane measurements to the correction planes (plane separation). Rotor Specific Calibration should be used when a ]arge cross effect is noted between correction planes separated by a small distance. Rotor Specific Calibration is also useful when the result of rotor weight and balance speed approaches or slightly exceeds the weight-speed squared (Wn2) rating of the machine, or when the rotor deforms while balancing (e.g., fan blades with variable pitch). Balancing machines employing offset roller bearings, which significantly affect the stiffness of the support bearing system, will also benefit from the employment of Rotor Specific Calibration. 4 1 End Drive U2 Drive power 7.5 kW Balancing speed 1. gear 60 - 580 rpm Balancing speed 2. gear 110- 1120 rpm Drive shafts Drive Shaft 250 Nm , Drive Shaft 80 Nm 4.1 1 Rotor locking device - end drive 4.2 1 Belt drive BU 4/5 Drive power 7.5 kW Belt driven diameter 20 - 600 mm Balancing speeds based upon 100 mm belt driven diameter: 140- 1460 rpm, 200-2000 rpm, 350 - 3640 rpm 4.3 1 Rotor locking device - belt drive 5 1 Electrical drive and control for variable balancing speed, consisting of: control cabinet prepared for installation of the measuring unit with: - frequency converter for speed setting range 1 : 10 and energetic recovery system - operation devices and contactors
            workpiece weight 100 - 3.000 kg
            workpiece length 5.000 mm
            diameter 1.260 - 1.600 mm
            Control CAP920
            total power requirement 11 kW
            weight of the machine ca. 20 t
            dimensions of the machine ca. 20" Container m
            Description :
            Mobile balancing system "SCHENCK" for use anywhere in the world

            The balancing system is permanently installed in a 20" open-top container.
            The container is equipped with everything you need for balancing

            • Lighting
            • Metal base plate 12,000 kg as a base plate for accuracy
            • Compressor for working air supply distributed in the container
            • Compressed air connections.
            • A circumferential power strip
            • A tool cabinet equipped with tools
            • A hydraulic lifting device for aligning the container from the outside
            • In addition to a tarpaulin for the roof, the container also comes with
            movable roof segments made of sheet metal.
            • The container has a central plug through which the container can be connected
            can be supplied with the required 380V voltage.

            The system has been approved by Schenck and test protocols are available

            On the following pages please find the specification for
            1 Schenck balancing machine, type HM 40/HM 20
            U/BU with measuring unit CAB 920 SmartTouch

            We like to give you some technical comments to this balancing machine.
            This machine exists in its basic version of a HM 40 U/BU. Additionally we are
            offering a special pair of add. pedestals type HM 20 which can be easily
            exchanged against the HM 40 pedestals. The HM 20 pedestals will enable you to
            accommodate also small pump rotors into the machine.

            The advantages are: only one machine base and end and belt drive with one
            electrical control (space cost-saving)
            The machine is installed in a open Top 20” Container as a safety enclosure.
            (space and cost-saving)

            The HM 40/20 U/BU covers a wide range of rotor types due to rotor weight,
            dimension and balancing tolerances. This may also require fiexibility in
            balancing speeds.

            Therefore we have quoted the machine together with an electrical drive with
            squirrel cage motor with frequency converter for variable speed.

            The offered measuring unit CAB 920 is a computerized high-end unit and
            especially developed to fulfil advanced balancing tasks. Data input is
            extremely simple through the "Easy Mode" guiding the Operator perfectly.
            Unbalance visualization is realized by big vector meter displays on a high
            contrast TFT colour monitor with touch screen function. The integrated
            Industrial PC runs the unique CAB 920 balancing software and provides access to
            the balancing Data for direct printouts or via PC network. CAB 920 can be
            adapted to specific needs by additional software packages.

            For quick and accurate finding of the angular position of the measured
            unbalance on the rotor by using the belt-drive the software extension 'angle
            indexing" is included in the delivery extent of both measuring units. When
            reaching the correet unbalance angle it will be displayed on the measuring unit.

            Due to the method of correction (grinding at a [arger surface area) the vector
            indication is of advantage.

            Machine mode: HM 40/20 U/BU
            Year of manufacturing: 2012/2021
            Manufacturing number: RPHF02I7
            Item Extent of delivery
            Pair Bearing Pedestals HM 40
            Rotor weight for symmetric bad 3000 kg
            for each bearing pedestal max. 1500 kg
            Largest rotor diameter above machine bed 1600 mm
            Distance between bearing centres (belt drive between pedestals) min. 155
            mm
            upward static bearing loads for counter bearing with roller 3000 N
            Limit value of permanent calibration 710 x 1 0E6 kg/min'

            1.1 1 Pair of Roller Bearing lnserts HM 40
            adjustable for journal bearing diameters

            1.2 1 Pair of Roller Bearing Inserts HM 40
            adjustable for journal bearing diameters
            1.3 1 Pair Bearing Pedestals HM 20
            Rotor weight for symmetric bad
            for each bearing pedestal max.
            Largest rotor diameter above machine bed
            Distance between bearing centres (left drive between pedestals)
            upward static bearing loads for counter bearing with roller
            Limit value of permanent calibration

            1 Pair of Roller Bearing lnserts
            adjustable for journal bearing diameters 9-70 mm
            1 Pair of Roller Bearing lnserts
            adjustable for journal bearing diameters 70-140 mm
            2 Set of counter bearings (Hold-down bracket)
            The balancing machine is equipped for safety reasons with one set of counter
            bearings size HM 40 and one set size HM 20 to absorb upward bearing loads. The
            counter bearings are hinged and tHting out of the way for easy rotor loading
            and unboading. Each set is consisting of:
            - 1 x counter bearing with roh (negative bad bearing for overhanging rotors)
            - 1 x counter bearing with sliding piece
            1.7 2 Axial thrust stops mounted on machine base
            Two axial thrust stops to be mounted on machine base for babancing big rotors
            in overhanging position.
            2 1 Machine Bed
            with roller chain and two T-slots for moving the pedestals
            easily along the machine base
            bed Iength in total
            consisting of 5.000 mm
            1 x3000mm, 1 x2000mm

            3 1 Measuring Unit
            with: Operating System Windows 10 loT Enterprise 2016 LTSB
            - Direct data input without keyboard via Touch-Screen-Display
            - Easy Mode for simplified data input and display of results
            - Indication of the result via big vectormeter and numerical displays
            - Workshop tried and tested industrial PC
            - Easy data export via front side USB
            - Networking capability
            - Optimized signal processing for high accuracy via Schenck MMD-digital filter
            - Intelligent self-diagnostics of the measuring electronics
            - Modular, service friendly System design
            - Operation using Windows standard procedures
            - Measurement of dynamic, static and couple unbalance
            - Optimised menu functions
            - Rotorfile Wizard
            - Possibility to connect drawings or instructions to rotor files
            - User level administration with individual profiles
            - Numerous software modules available
            - mcl. Software 'Tolerance Calculation to [SO 21940-11
            - mcl. single, key- and index compensation
            - mdl. measurement during run-up
            - Advanced print manager
            - Log report in pdf format
            - Archiving in measurement value database in MS-Excel compatible format
            - User dialog can be selected between English/German

            Measuring range
            100 – 5000 rpm
            Minimum achievable residual unbalance (Umar)
            acc. ISO 2953 for each plane per kg rotor weight
            with belt-drive 0.1 gmm/kg
            with end-drive 0.5 gmm/kg
            but for HM 20 pedestals not less than 0.8 gmm
            but for HM 40 pedestals not less than 4.0 gmm
            Value refers to the measuring speed of 1000 rpm
            Unbalance reduction ratio (URR) up to 95%

            3.1 1 Indexing manually
            to exactly transfer the measured unbalance angle to the rotor (manual indexing).

            3.2 1 Software "Rotorspecific Calibration"
            Our optional Rotor Specific Calibration software allows a "fine tuning" of the
            machine to compensate for balancing tooling whose dynamic stiffness is
            insufficient. The Rotor Specific Calibration software will improve the ability
            to transpose the bearing plane measurements to the correction planes (plane
            separation). Rotor Specific Calibration should be used when a ]arge cross
            effect is noted between correction planes separated by a small distance.
            Rotor Specific Calibration is also useful when the result of rotor weight and
            balance speed approaches or slightly exceeds the weight-speed squared (Wn2)
            rating of the machine, or when the rotor deforms while balancing (e.g., fan
            blades with variable pitch). Balancing machines employing offset roller
            bearings, which significantly affect the stiffness of the support bearing
            system, will also benefit from the employment of Rotor Specific Calibration.

            4 1 End Drive U2
            Drive power 7.5 kW
            Balancing speed 1. gear 60 - 580 rpm
            Balancing speed 2. gear 110- 1120 rpm
            Drive shafts Drive Shaft 250 Nm , Drive Shaft 80 Nm

            4.1 1 Rotor locking device - end drive

            4.2 1 Belt drive BU 4/5
            Drive power 7.5 kW
            Belt driven diameter 20 - 600 mm
            Balancing speeds based upon 100 mm belt driven diameter:
            140- 1460 rpm, 200-2000 rpm, 350 - 3640 rpm

            4.3 1 Rotor locking device - belt drive
            5 1 Electrical drive and control
            for variable balancing speed, consisting of:
            control cabinet prepared for installation of the measuring unit with:
            - frequency converter for speed setting range 1 : 10 and energetic
            recovery system
            - operation devices and contactors




          Datasheet
          Request / Contact
          •   
          •   
          • 1  
          •   
          •   

            Профіль торговця: SKM Industriemaschinen

          Зв'язатися з трейдером



            СКМ промислова техніка
           Röntgenstr. 3
            89264 - Вайсенхорн
            Німеччина
            + 49 (0) 7309 954 986 "> + 0 49 0 7309 954
            + 49 (0) 7309 954 986 1
            info@skm-maschinen.de
            www.skm-maschinen.de

          Профіль Трейдера

          Ласкаво просимо до компанії SKM Industrial Machinery

          У нас ви можете довіряти фахівця. Ми - Ваш компетентний партнер для використаних та нових верстатів. Ми пропонуємо найширший вибір - від простих свердлильних таблиць до складного поворотного центру осі 7.

          Незалежно від того, чи нове або уживане обладнання, сервісні роботи, введення в експлуатацію, запасні частини, розбирання та організація транспортування, лізингу та фінансування - з SKM Industrial Machinery ви вибираєте компетентного та надійного партнера.

          У нашому бізнес-приміщенні і на нашому сайті Ви можете знайти надійну технологію для ЧПУ для Ваших особистих потреб, незалежно від того, чи це найточніше буріння, фрезерування, згинання або токарні роботи. Звичайно, ми також пропонуємо комплексне обслуговування запасних частин для промислового обладнання. Ми пропонуємо незалежні консультанти з усіх аспектів верстатів.

          Незалежно від того, чи плануєте ви нові інвестиції, чи мають поточні виробничі проблеми або волієте покладатися на якісну машину з ЧПУ.

          СКМ промислова техніка
          Röntgenstr. 3
          89264 Weißenhorn
          Німеччина

          Тел .: + 49 (0) 7309 / 954 986-0
          Факс: + 49 (0) 7309 / 954 986-1

          E-Mail: info@skm-maschinen.de
          www.skm-maschinen.de





          Other used metal working machines are available online
          Finding other used metal working machines is just a click away

          Metal working machines come in a huge variety and shapes and sizes and have an equally large number of functions and applications. Handy men and business owners alike need quality metal working equipment that won't break the bank. Investing in used machines is the ideal compromise. You don't have to sacrifice quality in the name of money when you invest in used machines. Lathes, presses and other used metal working machines are available at LagerMaschinen. The advantages of shopping online for other used metal working machines are clear: you can shop quickly and easily from home or office, anytime day or night, and you can filter your searches based on location, price or brand name in order to find the best drills, saws or other used metal working equipment for your needs.

          All other used metal working machines at your fingertips

          No matter what sector you work in, metal working equipment often plays a crucial role in your business's efficiency and productivity. Given the current economy, buying new equipment isn't always a feasible option for many businesses. That's where LagerMaschinen steps in. From cylindrical grinding machines to machining centres and any other used metal working machines in between, you can find the best selection of used machines at LagerMaschinen. LagerMaschinen's user-friendly search platform puts Europe's biggest machinery marketplace at your fingertips. The ability to browse for large-scale machines online takes the hassle out of the machine buying experience. Whether you're looking for planers, presses, lathes or any other used metal working machines, you'll find the best selection at LagerMaschinen.

          SKM Industriemaschinen   89264 - Weißenhorn Röntgenstr. 3 Deutschland
          SKM Industriemaschinen

          Röntgenstr. 3



          Contact Trader


            SKM Industriemaschinen
           Röntgenstr. 3
            89264 - Weißenhorn
            Deutschland
            +49 (0) 7309 954 986 0
            +49 (0) 7309 954 986 1
            info@skm-maschinen.de
            www.skm-maschinen.de
            Contact person:

           




          Machine category


          Abkantpresse - hydraulisch · Absauggerät · Auswuchtmaschine · Bandanlage · Bohr- und Fräsmaschine · Exzenterpresse - Doppelständer · Gewinderollmaschine · Kaltkreissäge · Langdrehautomat · Ofen - Gas · Rohrbiegemaschine · Schweißdrehtisch · Schweißdrehtisch - rund · Sicken- und Bördelmaschine · Stemmmaschine · Tafelschere - hydraulisch · Tafelschere - mechanisch · Vertikaldrehmaschine · Werkstattpressen - hydraulisch · Werkzeugaufnahme · Werkzeugschränke ·