Injection-moulding machine (rubber)

clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱

---

Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 16 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1451 bar - Spec. injection pressure increased: 2205 bar - Nozzle path: 530 mm - Operating hours: 54716 h - Pump drive power: 11 kW - Weight without oil: 6,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm

clamping force 450 kN︱injection volume 135 cm³︱screw diameter 35 mm︱platen size 600 x 400 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for TPE - used, from testing department Including PIOVAN dosing unit clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - Clear width: 585 mm - Tool installation height min.: 185 mm - Max. stroke: 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 4 - Ejector stroke: 200 mm Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg

clamping force 250 kN︱injection volume 49 cm³︱screw diameter 25 mm︱platen size 300 x 300 mm︱

---

Condition: used, specification: C-frame injection moulding machine - used clamping unit: - clamping force: 250 kN - heating platen size: 300 x 300 mm - clamping/opening stroke: 330 mm - Closing direction: from below - Lateral ejector: yes - Ejector stroke/force: 115 mm / 12 kN Injection unit: - Injection volume max.: 49 cm³ - Screw diameter: 25 mm - Screw length: 16 - Screw speed max.: 250 rpm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE - Connected load: 55 kW/92 A - Weight approx.: 3,500 kg Various accessories are also available: - Injection unit (25 screw) - 2 heating plates - Funnel and various small parts

clamping force 270 kN︱injection volume 160 cm³︱screw diameter -- mm︱platen size 300 x 300 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for EPDM - used clamping unit: - clamping force: 270 kN - heating platen size: 300 x 300 mm - sliding table: no - Clamping direction: from below Injection unit: - Injection volume max.: 160 cm³ - Connected load: 3x 400 V, 50 Hz - Power: 20 kW - Weight approx.: 2.100 kg There are two identical systems available

clamping force 270 kN︱injection volume 160 cm³︱screw diameter -- mm︱platen size 300 x 300 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for EPDM - used clamping unit: - clamping force: 270 kN - heating platen size: 300 x 300 mm - sliding table: no - Clamping direction: from below Injection unit: - Injection volume max.: 160 cm³ - Connected load: 3x 400 V, 50 Hz - Power: 20 kW - Weight approx.: 2.100 kg There are two identical systems available

clamping force -- kN︱injection volume -- cm³︱screw diameter -- mm︱

---

Condition: used, Specification: Handling System REMAK-Robot - used type: RF5T-CNC/R driving range: - motor-axis stroke Z-axis: 2.000 mm speed: 3.200 mm/s - Teescope Y-axis stroke: 1,500 mm Speed: 4,400 mm/s X-axis stroke: 500 mm Speed: 1,100 mm/s - Pneum. Axes: B = 0/+90 o. +180 degrees C = 0/+90 degrees - Vacuum: 2 x vacuum generator type EZM 131 - Gripper: 2 x spring-return valves - Permissible load (gripper + workpiece): 5.0 kp - E-connection: 480V, 60Hz - Connected load: approx. 3.5 kW, 16A - Control: Bosch Rho3.0, PHG 16 Vers.8.x

clamping force 270 kN︱injection volume 160 cm³︱screw diameter -- mm︱platen size 300 x 300 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for EPDM - used clamping unit: - clamping force: 270 kN - heating platen size: 300 x 300 mm - sliding table: yes - Clamping direction: from below Injection unit: - Injection volume max.: 160 cm³ - Connected load: 3x 400 V, 50 Hz - Power: 20 kW - Weight approx.: 2.100 kg There are two identical systems available

clamping force 1.300 kN︱injection volume 230 cm³︱screw diameter 45 mm︱platen size 685 x 685 mm︱

---

Condition: used, Specification: injection moulding machine for TPE - used including Koch dosing unit clamping unit: - clamping force: 1.300 kN - heating platen size: 685 x 685 mm - Clear distance between tie bars: 470 x 470 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 225 mm Injection unit: - Screw diameter: 45 mm x 18D - Injection volume max.: 230 cm³ - Injection part weight: 210 g/hp - Max. injection pressure: 1,670 bar - Screw circumferential speed: 75 m/min - Cylinder heating: 4x 2,200 W - Nozzle heating: 600 W - Connection value: 3x 400 V, 50 Hz - Electrical connection (back-up fuse): 100 A - Weight approx.: 6,380 kg - Oil filling: 260 litres - Operating hours approx.: 64,903 h

clamping force 450 kN︱injection volume 99 cm³︱screw diameter 30 mm︱platen size 860 x 320 mm︱closing stroke 406 mm︱

---

Condition: used, Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083 Clamping unit: - Clamping force: 450 kN - Opening travel: 406 mm - Heating plate size: 860 x 320 mm - Mould height min.: 264 mm - Max. plate spacing: 464 mm - Ejector stroke: 20 mm - Ejector force: 20 kN Injection unit: - Screw diameter: 30 mm - Screw length L/D: 17 - Dosing stroke: 140 mm - Stroke volume max.: 99 cm³ - Max. spray weight: 114 g - Screw speed: 20 - 300 rpm - Injection flow: 106 cm³/s - Injection flow increased: 71 cm³/s - Special injection pressure: 1450 bar - Spec. injection pressure increased: 2210 bar - Nozzle path: 200 mm - Operating hours: 54716 h - Pump drive power: 15 kW - Weight without oil: 5,500 kg - Dimensions L/W/height: 2,500 x 1,900 x 3,680 mm

clamping force 270 kN︱injection volume 160 cm³︱screw diameter -- mm︱platen size 300 x 300 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for EPDM - used clamping unit: - clamping force: 270 kN - heating platen size: 300 x 300 mm - sliding table: yes - Clamping direction: from below Injection unit: - Injection volume max.: 160 cm³ - Connected load: 3x 400 V, 50 Hz - Power: 20 kW - Weight approx.: 2.100 kg There are two identical systems available

clamping force 500 kN︱injection volume 220 cm³︱screw diameter -- mm︱platen size 500 x 320 mm︱

---

Condition: used, Specification: C-frame injection moulding machine for EPDM - used clamping unit: - clamping force: 500 kN - heating platen size: 500 x 320 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo - Number of core pulls: 1 Injection unit: - Injection volume max.: 220 cm³ - Connected load: 3x 400 V, 50 Hz

clamping force 1.550 kN︱injection volume 135 / 49 cm³︱screw diameter 35 / 25 mm︱platen size -- mm︱

---

Condition: used, Specification: injection moulding machine for TPE - used type: K-TEC 155 S/2F clamping unit 1550: - Clamping force: 1,550 kN - Clear column spacing: 500 x 500 mm - Max. platen spacing: 950 mm - Platen spacing min.: 650 mm - Opening stroke min.: 300 mm - Ejector stroke: 180 mm Injection unit 1: - Screw diameter: 35 mm - Injection volume max.: 135 cm³ - Injection part weight: 125 g - Injection pressure max.: 1.964 bar Injection unit 2: - Screw diameter: 25 mm - Injection volume max.: 49 cm³ - Injection pressure max.: 2.254 bar - Connection value: 3x 400 V, 50 Hz - Engine power: 37 kW - Total heating power: 14.8 kW - Electrical connection (back-up fuse): 160 A - Dimensions W/D/H approx.: 6.200 x 1.750 x 2,100 mm (see sketch) - Weight approx.: 9.000 kg - Operating hours approx.: 53.176 h

clamping force 500 kN︱injection volume 64 cm³︱screw diameter 25 mm︱platen size 270 x 270 mm︱closing stroke 350 mm︱

---

Condition: used, Specification: injection moulding machine for liquid silicone LSR - used incl. 2KM dosing system for 25 liter Hobbocks and a handling system WEMO W-HP7/8 year 2011. clamping unit: - clamping force: 500 kN - Opening stroke: 350 mm - Mould installation height: 200 mm - Distance between clamping platens: 550 mm - size of heating platens: 270 x 270 mm - Heating: 6,5 kW - Ejector stroke: 125 mm - Ejector force: 30 kN Injection unit: - Screw diameter: 25 mm - Injection volume approx.: 64 cm³ - Injection flow: 112 cm³/s - Spec. injection pressure increased: 2,470 bar - Nozzle stroke: 240 mm - Nozzle contact pressure: 70 kN - Operating voltage: 3x 400V, 50 Hz - Pump motor: 15 kW - Total power: 21,5 kW - Weight without oil: 2,230 kg - Dimensions L/W/height: Sensor equipment: - WEMO Automation GmbH Handling Make: W-HP7/8 - Year of construction 2011 - Dosing unit for liquid silicone, Make 2KM, for 25 litre hobbocks

clamping force 1.500 kN︱injection volume 115,4 cm³︱screw diameter 35 / 18 mm︱platen size 740 x 740 mm︱

---

Condition: used, Specification: injection moulding machine for TPE - used type: BA 1500/400H/125L CDC clamping unit 1500: - clamping force: 1.500 kN - heating platen size: 740 x 740 mm - Clear distance between tie bars: 500 x 500 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 160 mm Injection unit 1 400: - Screw diameter: 35 mm x 22.9D - Injection volume max.: 115.4 cm³ - Injection part weight: 105 g - Max. injection pressure: 1,096 bar - Screw speed max.: 349 rpm Injection unit 2: - Screw diameter: 18 mm - Connection value: 3x 400 V, 50 Hz - Control voltage: 24 VDC - Electrical connection (back-up fuse): 125 A - Dimensions W/D/H approx.: 5,300 x 3,100 x 2,100 mm (see sketch) - Weight approx.: 11,000 kg - Operating hours approx.: 77,954 h The system is not functional without repair work. Screen does not boot up.

clamping force 2500 kN︱injection volume 2x 190 cm³︱screw diameter 45 mm︱screw length 22 D ︱platen size 510 x 670 mm︱

---

Condition: used Specification: Vertical Injection Moulding Machine for Rubber - second-hand - clamping force: 2500 kN - screw diameter: 45 mm - screw length: 22 D - screw speed: max. 300 rpm - injection volume: 2 x 190 cm3 - Injection pressure: 1900 bar - Number of heating zones: 5 - open nozzle with nozzle head - Clear column spacing: 510 x 670 - Mains supply voltage: 380 V, 50 Hz - Machine weight approx.: 7.8 t without oil filling - Oil filling approx.: 260 litres, 230 kg Two identical machines (built 1991, 1993) are available.

clamping force 2500 kN︱injection volume 2x 190 cm³︱screw diameter 45 mm︱screw length 22 D ︱platen size 510 x 670 mm︱

---

Condition: used Specification: Vertical Injection Moulding Machine for Rubber - second-hand - clamping force: 2500 kN - screw diameter: 45 mm - screw length: 22 D - screw speed: max. 300 rpm - injection volume: 2 x 190 cm3 - Injection pressure: 1900 bar - Number of heating zones: 5 - open nozzle with nozzle head - Clear column spacing: 510 x 670 - Mains supply voltage: 380 V, 50 Hz - Machine weight approx.: 7.8 t without oil filling - Oil filling approx.: 260 litres, 230 kg Two identical machines are available.

clamping force 1600 kN︱injection volume 2x 113 cm³︱screw diameter 40 mm︱screw length 21 D ︱platen size 410 x 570 mm︱

---

clamping force 300 kN︱injection volume 105 cm³︱screw diameter -- mm︱platen size 300 x 400 mm︱

---

Condition: used, Specification: Vertical C-frame Injection Moulding Machine for rubber - second-hand suitable for vulcanising together extruded rubber profiles to sealing frames or for the production of small precision moulded parts. The C-frame design ensures very good mould accessibility accessibility of the tools from three sides, so that when vulcanising the necessary space when vulcanising sealing profiles. to be able to work comfortably even with multiple tools. be able to work comfortably. Injection unit: - Injection volume approx.: 105 cm³ - Injection pressure approx.: 1,800 bar Clamping unit: - Clamping force: 300 kN - Size of heating platen: 300 x 400 mm - Clamping speed: 100 mm/sec - Heating power per platen: 3 kW - Total power with sliding table: 9 kW With alternating sliding table, i.e. two moulds can be used at the same time. two moulds at the same time. - Dimensions approx.: 2.400 x 1.400 x 2.600 mm - Weight approx.: 3,000 kg